Guide

Key hard to turn, sticking or stuck in the lock? Causes and fixes

A sticking key usually points to something cheap to fix, if you catch it before the lock gives out. Find your symptom below. The fix might be a new key, a cleaning, a strike adjustment or, this close to the ocean, a new lock.By Pacific Beach LocksmithUpdated November 8, 20265 min read

Start with the key

Before you blame the lock, try another key to the same door.

The original works, the new copy doesn't

That's a bad duplicate. A copy cut a fraction too deep or too shallow, or slightly out of line, goes in but won't turn unless you jiggle it. Copies of copies get worse each time, and a fresh copy can have burrs that catch on the pins. Have it recut from the original, or have a locksmith cut one to the correct depths.

Every key is stiff, and the oldest is worst

Keys wear. Rounded cuts no longer lift the pins to the right height, so the key needs a wiggle. New keys cut to the correct depths fix it, and so does rekeying the lock to a fresh set. Keep forcing a worn key and it can snap off in the door, and then you'll want the guide on what to do when a key breaks off.

It goes in but won't turn, or won't come out

If a good key slides in but won't turn, something inside is keeping the pins from lining up. Near the coast that's usually sand, salt crystals and old lubricant gone gummy. Dry, pitted pins and tired springs come later. Make sure it's the right key, then clean and dry-lube the cylinder as described further down.

A key stuck in the lock

A pin-tumbler key only comes out when the cylinder is back where it was when the key went in. Turn it fully back, then pull straight out with a slight up-and-down wiggle. If it still catches, a burr on a new copy or a damaged pin is probably holding it. A short burst of dry lube can free it. Don't pull hard with pliers, because that's how keys snap.

It only turns when you push or pull the door

This one is rarely the lock. If you have to lean on the door, pull it toward you or lift the handle to get the deadbolt across, the bolt is rubbing on the strike plate because the door and frame no longer line up. To check, open the door and turn the key with the bolt in open air. If it turns smoothly, the lock is fine. The usual causes:

  • A sagging door. Loose screws in the top hinge let the latch side drop. Tightening them, or swapping one for a long screw into the framing, often lifts it back.
  • A strike that has shifted, or a frame that has settled, so the strike needs moving or its opening enlarged.
  • Swelling or weatherstrip. A wood door that swells on damp days, or new weatherstrip pushing the door outward, puts the bolt under load.

Strike and hinge adjustments are routine lock repair. Sliding glass doors have their own version, covered under patio door lock repair.

It turns but the bolt doesn't move, or it works from one side only

If the key turns freely, sometimes all the way round, and the bolt stays put, the link between the cylinder and the bolt has failed. On a deadbolt that's usually the tailpiece, the flat bar on the back of the cylinder that drives the bolt. On a mortise lock it's the cam. Either one can break or slip out of place.

The same fault explains a lock that works from one side only. If the inside thumbturn throws the bolt but the outside key spins, the outside cylinder or its tailpiece is at fault. If the key works and the thumbturn doesn't, look at the inside half. Sometimes the tailpiece was cut too short or set at the wrong angle when the lock went in. Parts often exist, but on a cheap or worn lock, replacing it is usually the better money, and the guide to rekeying or replacing a lock helps with that call.

Salt, sand and what to put in a lock

Within a few blocks of the water, in Mission Beach or on the ocean side of PB, salt spray and fine sand get into every keyway. The routine is the same one in our guide to locks in salt air:

  1. Blow loose sand out of the keyway with a few puffs of canned air.
  2. Clean the keyway with a lock-safe cleaner and let it dry.
  3. Give it a short burst of PTFE dry lubricant, then work the key in and out a dozen times.

What not to spray: regular WD-40 or household oil. WD-40 is more cleaner than lubricant and washes out what's left of the factory lube. Both leave a film that holds sand and dust and slowly gums up the pins. Graphite is fine in a clean lock but builds up over time, and mixed with oil it turns to paste.

If the key is stiff again within weeks of a proper cleaning, the cylinder is probably pitted or worn inside.

A five-minute fix or a finished lock?

  • Bad copy or worn key: a new key, cut properly.
  • Sandy or dry cylinder that frees up after cleaning: clean and dry-lube, five minutes.
  • Turns only when you push the door: adjust the strike or hinges.
  • Key spins, bolt stays put: repair the tailpiece or cam, or replace a cheap lock.
  • Pitted, bubbling or green finish, or stiff again soon after cleaning: replace it with coastal-grade hardware.

Don't keep forcing it. A lock that sticks today can leave you on the doorstep next month, and then you need a lockout before the repair. If you rent, tell the landlord or manager first; the renter lock rules guide covers the basics. And the pricing FAQ explains how quotes work.

Questions people ask

What should I use to lubricate a sticky lock?

A PTFE dry lubricant, after you've cleaned the keyway with a lock-safe cleaner. One short burst, then work the key in and out a dozen times. Skip WD-40 and household oil, which gum up the pins and hold on to sand over time.

My key is stuck in the lock. How do I get it out?

Turn the key fully back to where it was when it went in, then pull straight out with a slight up-and-down wiggle. A short burst of dry lubricant can help. Don't yank it with pliers. If it won't come out, call a locksmith before it snaps.

Why does my new key copy not work when the original does?

Because the copy was cut slightly wrong. A tiny error in depth or alignment stops the pins lining up. Have it recut from the original or cut to the correct depths, and never copy the bad copy.

Rather talk it through?

Call or text and describe what's going on. If it needs a visit, you'll hear the price before we head out.

Call (858) 842-9337(858) 842-9337 Text us

Have your ID handy, plus something showing it's your home or car.