Sliding Door Locks

Sliding glass and patio door locks in Pacific Beach

Condos and bayfront units in Pacific Beach live on their sliding glass doors, and the latch on a slider is often the weakest lock in the home. We replace worn latches and mortise locks and add keyed or secondary locks. When a slider has stopped catching, though, the fix is often an adjustment to the rollers or the keeper rather than a new lock. It's all part of our residential locksmith service.

What we do

  • Worn latches and handle sets replaced
  • Mortise hook locks that no longer catch
  • Keyed sliding door locks
  • Foot bolts, pin locks and security bars
  • Anti-lift protection in the upper track
  • Roller and keeper adjustment
  • Corroded keepers and strikes replaced
  • Patio locks keyed to your house key where possible

When the latch will not catch

A slider that won't lock usually has one of three problems, and two of them aren't the lock.

  • The rollers. The panel rides on a roller near each end of its bottom edge. As they wear or pack with sand the panel drops, and the hook ends up below the keeper on the frame. Turning the adjustment screws to raise the panel often brings the latch back without a new lock.
  • The keeper and frame. The keeper may have worked loose or corroded, or the frame itself has moved. Usually the keeper can be cleaned and reset to line up with the hook; if it's corroded through, it gets replaced.
  • The lock itself. A hook that won't swing all the way out, a broken spring, a handle that spins, a lock body corroded solid. Those mean a new lock.

Don't force the handle on a door that won't latch, because a hook slammed into a misaligned keeper will bend. And if the rollers are worn out or the track is damaged, we'll tell you, rather than fit a new lock to a door that still won't line up.

Latches, mortise locks and keyed locks

Older and cheaper sliders often have a surface latch, a handle and small hook screwed to the inside face of the panel. Many newer doors use a mortise lock instead: a narrow lock body set inside the edge of the panel, with a curved hook that swings out to grab the keeper. Both come in a lot of sizes, so we match the old lock's screw spacing and hook position and avoid drilling new holes in the frame where we can.

If you want the slider locked from outside, for a patio you use as your main entry or a ground-floor unit you leave through the back, we fit a keyed lock and can often key it to match the front door, including the key override on a keypad or smart lock, so you carry one key. Not every slider lock takes a standard cylinder, so we'll tell you what fits before you choose.

Secondary locks and keeping the door in its track

The factory latch holds the door closed, and that's about all it does against someone determined to get in. Almost every slider is worth a second lock.

  • Foot bolts mount low on the panel and drop a pin into the sill when you press them with your foot, which makes them the easiest to use every day.
  • Pin locks go through the fixed and sliding frames where they overlap, so the panels can't slide or separate.
  • Security bars fold down across the door or lie in the bottom track. They're easy to see from outside, and the kind that lies in the track needs no drilling, which suits renters.
  • Anti-lift protection. If there's room above the panel, some sliders can be lifted off the bottom track, hook and all. Anti-lift blocks or screws in the upper track close that gap while leaving room to slide.

Our guide to securing a sliding glass door covers how sliders get defeated and what you can do about it yourself. If one has already been forced, start with our break-in repair service.

What salt and sand do to slider hardware

Bayfront units in Crown Point and along Riviera Dr and boardwalk units in Mission Beach take it hardest. Salt gets into the lock body, where steel parts touching the aluminum frame make the aluminum corrode faster, and sand packs the bottom track and grinds down the rollers. A door that's hard to slide also pulls the lock out of line, so keeping the track clean is part of looking after the lock.

Every couple of weeks, vacuum the bottom track and wipe it with a damp cloth. For the latch, use a dry lubricant made for locks, not oil, which holds on to sand.

Near the water, 316 stainless or coastal-rated parts are worth it where they're made, and we can clean the track and lubricate the rollers and lock while we're there. Our salt air hardware guide covers the rest of the house.

How pricing works for sliding door locks

The quote follows what the door needs. Adjusting rollers and resetting a keeper is the smallest job, and a new latch or mortise lock depends on the part your door takes. Secondary locks and anti-lift fixes are priced one by one, so you pick what you want.

Text photos of the latch, the panel edge and the keeper for a firm quote, confirmed at the door before we start. If the real problem is the rollers, you'll hear that first. More on how we quote a job.

What to have ready when you call

  • Photos of the latch, the panel edge and the keeper on the frame
  • Any brand name or label on the door frame or the old lock
  • Whether you want the slider lockable from outside with a key
  • How it behaves: will not latch, hard to slide, or latches but rattles
  • For condos and rentals, HOA or landlord approval if their rules require it

Common questions

My slider locks but rattles and pulls open a little. Is that normal?

No. It means the hook is barely catching the keeper, usually because the rollers have dropped or the keeper has moved. An adjustment often tightens it up, and a worn hook or keeper gets replaced. It's worth doing soon, since a door that gives with the latch on is easier to force.

Is a stick in the track as good as a secondary lock?

It stops the door sliding, but it does nothing if the panel can be lifted off its track, and it's easy to forget to put back. A pin lock or anti-lift block covers lifting, and a foot bolt is quicker to use every day.

I rent. Can I add a lock to the slider?

In most cases. A bar that sits in the bottom track needs no drilling at all. Foot bolts, pin locks and fold-down bars need only small holes, but ask your landlord or HOA before anything gets drilled. Our guide to lock rules for California renters explains the rest.

Can you get me in through the slider if I am locked out?

We'd normally open the front door instead. A slider with a bar, pin or foot bolt in place is built to resist being opened from outside, which is the point of fitting one. Either way it's a house lockout, and we check ID and proof that you live there before opening anything.

Sliding Door Locks in Pacific Beach

Call or text 7 am to 9:30 pm, every day. You'll get a price and an ETA from the locksmith who does the work.

Call (858) 842-9337(858) 842-9337 Text us

Have your ID handy, plus something showing it's your home or car.