Panic Bars & Door Closers

Panic bar and door closer repair for Pacific Beach businesses

The closer and the exit device take most of the abuse a commercial door gets. When the front door slams hard enough to rattle the glass, or the back door stops an inch short of the latch, one of them is usually the reason. We adjust and repair them, replace the ones that are worn out, and service storefront locks too.

What we do

  • Door closer adjustment: sweep, latch speed and backcheck
  • Replacement of leaking or worn-out closers
  • Panic bar and exit device repair and replacement
  • Doors that drag, sag or will not latch
  • Storefront aluminum door locks and cylinders
  • Rekeying exit device and storefront cylinders

Door closers: adjust or replace?

Most commercial closers are hydraulic. A spring shuts the door, and oil forced through small valves controls how fast. Three valves matter most.

  • Sweep speed controls the main swing, from fully open until the door nears the frame.
  • Latch speed controls the last few inches. Too slow and the door stops short of the latch; too fast and it slams.
  • Backcheck cushions the door when it's pushed or blown open hard, so it doesn't hit the wall or tear the arm loose.

Small turns are enough, and a valve backed out too far can leak.

No adjustment fixes a leaking closer. Oil under the door or streaks down the body mean the seals have gone, and a door that suddenly slams after years of behaving usually has the same problem. A closer can't be refilled, so it gets replaced, and so does one with a bent arm or one pulled out of the frame. Closers hidden in a storefront header or the floor adjust the same way, but a replacement has to fit the old one's pocket.

Doors that drag or will not latch

When a door won't close, the closer often gets blamed for something else, so we check the door first.

  • Sagging hinges or a worn pivot let the door rub the frame or threshold, and no closer pushes through that.
  • A strike out of line after the door or frame has shifted makes the door bump and bounce back.
  • Air pressure. A strong kitchen exhaust hood can make a door slam or stop it closing the last inch, depending on which way it swings.

We tighten or replace loose hinge screws and realign the strike, then set the closer to pull the door through the latch. A worn pivot or a bent frame is a bigger repair, and we'll say so first. Building entry doors that get propped and slammed all day are covered on our page for property managers and HOAs. Salt air wears out hinges, pivots and arms faster, and the coastal hardware guide explains what holds up. If someone damaged the frame trying to force the door, break-in repair comes first.

Panic bars and exit devices

An exit device, the push bar or pad across an exit door, lets anyone leave with one push and no key. From outside, the door may have a pull, a key cylinder or nothing at all, so on many back doors the latch is the only thing holding it shut.

A bar that sticks or won't spring back has worn or dirty internals. A latch that hits the strike instead of catching needs realigning. Vertical rod devices, which latch at the top and bottom of the door, drift out of adjustment, and the bottom latch wears as it drags. We repair what can be repaired, and a device worn past adjusting gets replaced with commercial-grade hardware.

Exit doors fall under the fire and building codes, and the local fire inspector or building official has the final word on what a door needs. We won't add chains, padlocks or slide bolts to a door with a panic bar.

Storefront locks, and the door that does not latch at night

Aluminum storefront door locks

Narrow aluminum and glass doors take locks built for their thin edge: a mortise deadlock with a hook bolt that swings into the frame to resist prying, or a mortise deadlatch that catches whenever the door closes and opens with a handle or paddle. Both usually take a threaded mortise cylinder with a cam on the back. If the key turns and nothing happens, look for a worn cam or a cylinder that has worked loose. A key that won't turn at all is covered in our guide to keys that stick or won't turn. After a staff change, these cylinders rekey like any other lock, and they can join a master key system.

Why an unlatched door is a nightly problem

The last person out pulls the door shut and leaves. If the closer is slow, the strike is off or the exit device isn't catching, the door stops a fraction short and looks closed, and anyone who tries it overnight walks in.

Every night, after the door closes, push or pull it without touching the handle. If it moves, it isn't latched.

The storefront security checklist covers the rest of the closing routine, and our commercial locksmith page covers rekeys and business lockouts.

How pricing works for closers and exit devices

An adjustment is labor only and usually quick, and a repair adds the parts that failed. A replacement depends on the hardware. A surface closer is simpler to swap than a concealed one, and a rim exit device simpler than vertical rods on a pair of doors. Aluminum, hollow metal and wood doors also mount differently.

Text photos of the hardware, the door edge and any model number for a firm quote before we come out, confirmed on arrival. The pricing FAQ covers how quotes work.

What to have ready when you call

  • Photos of the closer or exit device, the door edge and the frame
  • Any brand or model number printed on the hardware
  • What the door does: slams, drags, will not latch or sticks
  • Single door or a pair, and aluminum, metal or wood
  • Who approves the work, and a time before opening or after close

Common questions

Why does my door slam in the afternoon but close fine in the morning?

Probably wind, heat or both. The afternoon sea breeze pushes on the door, and closer oil thins as it warms, so a closer set on a cool morning can run fast by mid-afternoon. We set it for the conditions the door actually sees.

Can we dog the panic bar or prop the exit door open during business hours?

It depends on the door, and that's a question for the fire inspector rather than a locksmith. From a security point of view, a dogged or propped door is unlocked, so someone has to undo it at close every night.

Can you replace a panic bar with a regular lock?

Only on a door that isn't required to have one, which fire and building code decide, not us or the landlord. Where a panic bar is required, we repair it or replace it with another exit device.

Do you work on aluminum storefront doors?

Yes, on the locks, cylinders and closers. Narrow-stile aluminum doors have their own hook-bolt and deadlatch locks and mortise cylinders, often with a closer hidden in the header, and we work on all of those. Broken glass and damaged frames are a job for a glazier.

Panic Bars & Door Closers in Pacific Beach

Call or text 7 am to 9:30 pm, every day. You'll get a price and an ETA from the locksmith who does the work.

Call (858) 842-9337(858) 842-9337 Text us

Have your ID handy, plus something showing it's your home or car.